View AXK712125G_7709552.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

axk7, 8 narrow pitch (0.4mm) connectors p4 series narrow-pitch connectors for board-to-board and board-to-fpc connection features 1. 0.4 mm pitch and support for mated heights of up to 1.5 mm, 2.0 mm, 2.5 mm, 3.0 mm, 3.5 mm, and 4.0 mm. 2. high impact-resistant construction. 1) adoption of bellows-type contact structure. 2) it is constructed with impact dispersion keys inside the body to disperse shocks when dropped. a high level of shock resistance is ensured by dispersing impact over the four locations where the socket indentations and header protrusions are mated together. note: the following numbers of contacts are not supported due to suction surface factors. ?no retention ?ting: 18 contacts or less ?with retention ?ting: 22 contacts or less 3. construction makes designing devices easier. 1) the lower connector bottom surface construction prevents contact and shorts between the pcb and metal terminals. this enables freedom in pattern wiring, helping to make pcbs smaller. 2) guides are provided to take up any position shift and facilitate insertion. 3) the connector has a simple lock mechanism. 4. design makes ef?ient mounting. features a terminal ?tness of 0.08 mm, construction resistant to creeping ?x, and design that facilitates visual inspection of the soldered part. 5. compliance with rohs directive environmentally friendly, the connectors comply with europes rohs directive. cadmium, lead, mercury, hexavalent chromium, pbb and pbde are not used. 6. connectors for inspection available connectors for inspection are available that are ideal for modular unit inspection and inspection in device assembly processes. applications compact portable devices ?ellular phones, dvc, digital cameras, etc socket and header are mated socket header what is ni barrier construction? by providing an exposed nickel part on the gold (au) plated contact, solder creeping is prevented despite the ultra low profile. header side contact [contact] socket side contact note: construction makes solder creeping difficult because header side is formed at the same time. ni barrier exposed ni part cu ni au cross section of socket side contact what is v notch construction? by using the edge for the contacting part and increasing contact pressure per unit area, the effectiveness in removing flux and contaminants is increased compared to its predecessor. this is also effective in preventing the trapping of contaminants. [cross section of contacting part] without notch with v notch header side contact cross section socket side contact cross section the roll surfaces are in contact with each other, providing high contact reliability. since the contact is formed by bending thin plate, it has a spring-like quality. this construction helps make it resistant to dropping and twisting. impact dispersion key socket header connector bottom: create any thru-hole and pattern wiring.

insertion guide socket side contact header side contact simple lock mechanism 1.5mm pcb narrow-pitch connectors p4 fpc reinforcing plate before mating ideal for board-to-fpc connections after mating the simple lock mechanism ensures that the connector clicks into position when it is inserted for reliable single- action insertion on the pcb. this enables the number of pins to be doubled white the size re- mains the same as that for exist- ing fpc connectors. this, in turn, contributes to making products and equipment more compact. all rights reserved (c) copyright matsushita electric works, ltd.
axk7, 8 table of product types p4 (0.4 mm pitch): no retention tting p4 (0.4 mm pitch): with retention tting 1.5mm mated height ? : available for sale 14 16 20 22 24 26 28 30 32 34 36 38 40 42 44 50 54 60 64 70 80 90 100 ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? 2.0mm ? ? ? ? ? ? ? 2.5mm ? ? ? 3.0mm 3.5mm 4.0mm number of contacts 1.5mm mated height ? : available for sale 10 12 20 22 30 34 40 44 46 50 60 80 90 100 ? ? ? ? ? ? ? ? ? ? ? ? ? 2.0mm 2.5mm ? ? ? ? ? ? ? ? ? ? ? ? ? 3.0mm 3.5mm 4.0mm notes: 1. please contact us regarding numbers of contacts other than those given above. 2. * header comes with no positioning bosses. number of contacts ordering information stacking height 1: for mated height 1.5 mm 2: for mated height 2.0 mm 3: for mated height 2.5 mm and 3 mm 5: for mated height 4.0 mm

1: for mated height 1.5 mm, 2.0 mm and 2.5 mm 2: for mated height 3 mm and 4 mm surface treatment (contact portion / terminal portion) 5: au plating over ni / au plating over ni 7: au plating over ni / au plating over ni (for ni barrier product available)

5: au plating over ni / au plating over ni other specifications

y: v notch type product number of contacts (2 digits) packing g: 3,000 pieces with embossed tape 2 reels axk7: narrow pitch connector p4 (0.4 mm pitch) socket axk8: narrow pitch connector p4 (0.4 mm pitch) header functions 1: with removal and retention fitting, with positioning bosses 2: with removal and retention fitting, no positioning bosses 3: no removal and retention fitting, with positioning bosses 4: no removal and retention fitting, no positioning bosses axk all rights reserved (c) copyright matsushita electric works, ltd.
axk7, 8 product types 1. no retention tting notes: 1. regarding ordering units; during production: please make orders in 1-reel units. samples for mounting con rmation: please contact us. see regarding sample orders to con rm proper mounting on page 10. samples: small lot orders are possible. 2. the standard type comes with no positioning bosses. connectors with positioning bosses are available on-demand production. for this type of connector, 8th digit of the part number changes from 4 to 3. e.g. mated height 1.5 mm and 20 contacts for socket without retention tting: axk720135g 3. the 10th digit y in the header part number indicates the connector has v-notch. (for details, please refer to page 1.) 4. connectors of different mated height (3.0 mm and 4.0 mm) and different number of contacts are available on-demand production only. please contact us for more details. mated height number of contacts part number packing socket header inner carton outer carton ni barrier product: not available ni barrier product: available 1.5 mm 14 axk714145* axk714147* axk814145y* asterisk mark on end of part number; g: 3,000 pieces asterisk mark on end of part number; g: 6,000 pieces 16 axk716145* axk716147* axk816145y* 20 axk720145* axk720147* axk820145y* 22 axk722145* axk722147* axk822145y* 24 axk724145* axk724147* axk824145y* 26 axk726145* axk726147* axk826145y* 28 axk728145* axk728147* axk828145y* 30 axk730145* axk730147* axk830145y* 34 axk734145* axk734147* axk834145y* 36 axk736145* axk736147* axk836145y* 40 axk740145* axk740147* axk840145y* 44 axk744145* axk744147* axk844145y* 50 axk750145* axk750147* axk850145y* 54 axk754145* axk754147* axk854145y* 60 axk760145* axk760147* axk860145y* 70 axk770145* axk770147* axk870145y* 80 axk780145* axk780147* axk880145y* 90 axk790145* axk790147* axk890145y* 100 axk700145* axk700147* axk800145y* 2.0 mm 20 axk720245* axk720247* axk820145y* asterisk mark on end of part number; g: 3,000 pieces asterisk mark on end of part number; g: 6,000 pieces 24 axk724245* axk724247* axk824145y* 30 axk730245* axk730247* axk830145y* 34 axk734245* axk734247* axk834145y* 40 axk740245* axk740247* axk840145y* 50 axk750245* axk750247* axk850145y* 100 axk700245* axk700247* axk800145y* 2.5 mm 30 axk730345* axk730347* axk830145y* asterisk mark on end of part number; g: 3,000 pieces asterisk mark on end of part number; g: 6,000 pieces 40 axk740345* axk740347* axk840145y* 70 axk770345* axk770347* axk870145y* 2. with retention tting notes: 1. regarding ordering units; during production: please make orders in 1-reel units. samples for mounting con rmation: please contact us. see regarding sample orders to con rm proper mounting on page 10. samples: small lot orders are possible. 2. the standard type comes with no positioning bosses. connectors with positioning bosses are available on-demand production. for this type of connector, 8th digit of the part number changes from 2 to 1. e.g. mated height 1.5 mm and 10 contacts for socket with retention tting: axk710115g. however, 12 contacts header comes with no positioning bosses. 3. the 10th digit y in the header part number indicates the connector has v-notch. (for details, please refer to page 1.) 4. connectors of different mated height (2.0 mm and 4.0 mm) and different number of contacts are available on-demand production only. please contact us for more details. mated height number of contacts part number packing socket header inner carton outer carton ni barrier product: not available ni barrier product: available 1.5 mm 10 axk710125* axk710127* axk810125y* asterisk mark on end of part number; g: 3,000 pieces asterisk mark on end of part number; g: 6,000 pieces 12 axk712125* axk712127* axk812125y* 22 axk722125* axk722127* axk822125y* 30 axk730125* axk730127* axk830125y* 34 axk734125* axk734127* axk834125y* 40 axk740125* axk740127* axk840125y* 44 axk744125* axk744127* axk844125y* 46 axk746125* axk746127* axk846125y* 50 axk750125* axk750127* axk850125y* 60 axk760125* axk760127* axk860125y* 80 axk780125* axk780127* axk880125y* 90 axk790125* axk790127* axk890125y* 100 axk700125* axk700127* axk800125y* 2.5 mm 20 axk720325* axk720327* axk820125y* asterisk mark on end of part number; g: 3,000 pieces asterisk mark on end of part number; g: 6,000 pieces 40 axk740325* axk740327* axk840125y* 50 axk750325* axk750327* axk850125y* 60 axk760325* axk760327* axk860125y* 80 axk780325* axk780327* axk880125y* 90 axk790325* axk790327* axk890125y* 3.0 mm 20 axk720325* axk720327* axk820225y* asterisk mark on end of part number; g: 3,000 pieces asterisk mark on end of part number; g: 6,000 pieces 40 axk740325* axk740327* axk840225y* 50 axk750325* axk750327* axk850225y* 60 axk760325* axk760327* axk860225y* 80 axk780325* axk780327* axk880225y* 90 axk790325* axk790327* axk890225y* all rights reserved (c) copyright matsushita electric works, ltd.
axk7, 8 specifications 1. characteristics 2. material and surface treatment item speci cations conditions electrical characteristics rated current 0.3a/contact (max. 5 a at total contacts) rated voltage 60v ac/dc breakdown voltage 150v ac for 1 min. detection current: 1ma insulation resistance min. 1,000m ? (initial) using 250v dc megger (applied for 1 min.) contact resistance max. 70m ? measured based on the hp4338b measurement method of jis c 5402 mechanical characteristics composite insertion force max. 0.981n {100gf}/contacts contacts (initial) composite removal force min. 0.0588n {6gf}/contacts contacts (mated height 1.5 mm, without removal and retention tting) min. 0.1176n {12gf}/contacts contacts (mated height 1.5 mm, except without removal and retention tting) post holding force min. 0.981n {100gf}/contacts measures the maximum load in the post axial direction until removal environmental characteristics ambient temperature 55 c to +85 c no freezing at low temperatures soldering heat resistance max. peak temperature of 245 c infrared re ow soldering 300 c within 5 sec. soldering iron thermal shock resistance (header and socket mated) 5 cycles, insulation resistance min. 100m ? , contact resistance max. 70m ? sequence 1. 55 c, 30 minutes 2. ~ , max. 5 minutes 3. 85 c, 30 minutes 4. ~ , max. 5 minutes humidity resistance (header and socket mated) 120 hours, insulation resistance min. 100m ? , contact resistance max. 70m ? bath temperature 40 2 c, humidity 90 to 95% r.h. saltwater spray resistance (header and socket mated) 24 hours, insulation resistance min. 100m ? , contact resistance max. 70m ? bath temperature 35 2 c, saltwater concentration 5 1% h 2 s resistance (header and socket mated) 48 hours, contact resistance max. 70m ? bath temperature 40 2 c, gas concentration 3 1 ppm, humidity 75 to 80% r.h. lifetime characteristics insertion and removal life 50 times repeated insertion and removal speed of max. 200 times/hours unit weight mated height 1.5mm, 20 contacts; socket: 0.04g header: 0.02g part name material surface treatment molded portion heat-resistant resin (ul94v-0), black contact and post copper alloy contact portion: au plating over ni terminal portion: au plating over ni (except for thick of terminal) however, upper terminal of ni barrier production: exposed over ni retention tting portion copper alloy sn plating over ni (except for front terminal) 0 3 +3 0 all rights reserved (c) copyright matsushita electric works, ltd.
axk7, 8 dimensions (mm) 1. no retention fitting socket (mated height: 1.5 mm, 2.0 mm, and 2.5 mm) 1.11 (suction face) e 0.15 0.03 4.10 0.40 0.05 0.40 0.05 a b 0.01 0.08 5.10 3.75 (0.675)(0.675) c 0.80 0.80 1.11 (suction face) d 4.10 a b 0.1 max. 18 contacts general tolerance: 0.2 dimension table (mm) number of contacts/ dimension a b c d 14 5.1 2.4 2.8 16 5.5 2.8 3.2 20 6.3 3.6 1.6 22 6.7 4.0 2.0 24 7.1 4.4 2.4 26 7.5 4.8 2.8 28 7.9 5.2 3.2 30 8.3 5.6 3.6 34 9.1 6.4 4.4 36 9.5 6.8 4.8 40 10.3 7.6 5.6 44 11.1 8.4 6.4 50 12.3 9.6 7.6 54 13.1 10.4 8.4 60 14.3 11.6 9.6 70 16.3 13.6 11.6 80 18.3 15.6 13.6 90 20.3 17.6 15.6 100 22.3 19.6 17.6 mated height/dimension e 1.5mm 1.50 2.0mm 1.92 2.5mm 2.42 header (mated height: 1.5 mm, 2.0 mm, and 2.5 mm) a b 0.1 0.40 0.05 0.40 0.05 0.15 0.03 2.76 3.96 2.19 (0.29)(0.29) 3.38 3.96 (suction face) 1.20 c 0.76 0.76 0.08 1.31 0.10 0.03 d 1.20 (suction face) 2.76 3.96 a b 0.1 max. 18 contacts general tolerance: 0.2 dimension table (mm) number of contacts/ dimension a b c d 14 3.9 2.4 3.04 16 4.3 2.8 3.44 20 5.1 3.6 1.6 22 5.5 4.0 2.0 24 5.9 4.4 2.4 26 6.3 4.8 2.8 28 6.7 5.2 3.2 30 7.1 5.6 3.6 34 7.9 6.4 4.4 36 8.3 6.8 4.8 40 9.1 7.6 5.6 44 9.9 8.4 6.4 50 11.1 9.6 7.6 54 11.9 10.4 8.4 60 13.1 11.6 9.6 70 15.1 13.6 11.6 80 17.1 15.6 13.6 90 19.1 17.6 15.6 100 21.1 19.6 17.6 socket and header are mated 1.50 0.15 2.00 0.15 2.50 0.15 all rights reserved (c) copyright matsushita electric works, ltd.
axk7, 8 2. with retention fitting socket a c d b 0.1 0.40 0.05 0.80 0.50 0.80 0.10 0.03 fitting 0.15 0.03 1.11 (suction face) 4.10 f 5.10 3.75 0.60 (0.675)(0.675) 0.08 e e a b 0.1 a b 0.1 10 and 12 contacts 20 and 22 contacts general tolerance: 0.2 dimension table (mm) number of contacts/ dimension a b c d e 10 5.90 1.60 4.60 2.00 12 6.30 2.00 5.00 2.40 20 7.90 3.60 6.60 2.80 22 8.30 4.00 7.00 30 9.90 5.60 2.80 8.60 34 10.70 6.40 3.60 9.40 40 11.90 7.60 4.80 10.60 44 12.70 8.40 5.60 11.40 46 13.10 8.80 6.00 11.80 50 13.90 9.60 6.80 12.60 60 15.90 11.60 8.80 14.60 80 19.90 15.60 12.80 18.60 90 21.90 17.60 14.80 20.60 100 23.90 19.60 16.80 22.60 mated height/dimension f 1.5mm 1.50 2.5mm, 3.0mm 2.42 4.0mm 3.42 header 0.40 0.05 0.15 0.03 a b 0.1 1.20 2.76 2.19 0.76 c d 0.50 0.10 0.03 fitting (suction face) f 3.96 3.38 0.60 (0.29)(0.29) 0.08 e e a b 0.1 a b 0.1 10 and 12 contacts 20 and 22 contacts general tolerance: 0.2 dimension table (mm) number of contacts/ dimension a b c d e 10 3.10 1.60 1.94 1.64 12 3.50 2.00 2.34 2.04 20 5.10 3.60 3.94 2.80 22 5.50 4.00 4.34 3.20 30 7.10 5.60 2.80 5.94 34 7.90 6.40 3.60 6.74 40 9.10 7.60 4.80 7.94 44 9.90 8.40 5.60 8.74 46 10.30 8.80 6.00 9.14 50 11.10 9.60 6.80 9.94 60 13.10 11.60 8.80 11.94 80 17.10 15.60 12.80 15.94 90 19.10 17.60 14.80 17.94 100 21.10 19.60 16.80 19.94 mated height/dimension g 1.5mm, 2.0mm, 2.5mm 1.31 3.0mm, 4.0mm 2.26 socket and header are mated. 3.00 0.15 2.50 0.15 1.50 0.15 all rights reserved (c) copyright matsushita electric works, ltd.
axk7, 8 embossed tape dimensions (unit: mm, common for respective contact type, socket and header) tape dimensions (conforming to jis c 0806-1990. however, some tapes have mounting hole pitches that do not comply with the standard.) tape i tape ii 1.75 c d a 0.3 4 2 1.5 dia. +0.1 0 pull out direction 1.75 c d a 0.3 4 2 pull out direction b 1.5 dia. +0.1 0 reel dimensions (conforming to eiaj etr-7002) f e 1 top cover tape emboss carrier tape dimension table (mm) 1. no retention fitting 2. with retention fitting 3. connector orientation with respect to direction of progress of embossed tape 1) no retention tting 2) with retention tting mated height number of contacts type of taping a b c d e f quantity per reel common for socket and header: 1.5 mm, 2.0 mm, 2.5 mm, and 3.0 mm max. 18 tape i 16.0 7.5 8.0 17.5 380 3,000 20 to 70 tape i 24.0 11.5 8.0 25.5 380 3,000 80 to 100 tape ii 32.0 28.4 14.2 8.0 33.5 380 3,000 mated height number of contacts type of taping a b c d e f quantity per reel common for socket and header: 1.5 mm, 2.0 mm, 2.5 mm, and 3.0 mm header: 4.0 mm max. 18 tape i 16.0 7.5 8.0 17.5 380 3,000 20 to 60 tape i 24.0 11.5 8.0 25.5 380 3,000 70 to 90 tape ii 32.0 28.4 14.2 8.0 33.5 380 3,000 100 tape ii 44.0 40.4 20.2 8.0 45.5 380 3,000 socket: 4.0 mm max. 18 tape i 16.0 7.5 8.0 17.5 380 2,000 20 to 60 tape i 24.0 11.5 8.0 25.5 380 2,000 70 to 90 tape ii 32.0 28.4 14.2 8.0 33.5 380 2,000 100 tape ii 44.0 40.4 20.2 8.0 45.5 380 2,000 type direction of tape progress common for p4 socket header note: there is no indication on this product regarding top-bottom or left-right orientation. type direction of tape progress common for p4 socket header note: there is no indication on this product regarding top-bottom or left-right orientation. all rights reserved (c) copyright matsushita electric works, ltd.
axk7, 8 nar r o w pit c h connector p4 (0.4 mm pit c hes) f o r inspection us a g e connector for inspection usage applications with 3,000 insertion and removal times socket header features 1. 3,000 insertion and removals (when as recommended) from the 50 insertion and removals of standard type, up to 3,000 insertion and removals (with recommended insertion and removal) are possible for use in inspection. ideal for inspection of module units and inspection during the device assembly process 2. same external dimensions and foot pattern as standard type. since shape is the same as standard type, inspection is possible without interfering with devices in the vicinity of standard connectors. 3. easier to mate due to the simplicity of the locking mechanism less mating force is required for insertion and removal. (connector is intended for inspection purposes mating strength is not good enough for applications with strong shock and vibration) table of produt types 1.5mm mated height product name p4 for inspection p4 for inspection with fitting ? : available for sale 10 12 14 16 20 22 24 26 30 34 36 40 42 44 46 50 54 60 70 80 90 100 ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? 1.5mm ? ? ? ? ? ? ? ? ? ? ? ? notes: 1. you can use with each mated height in common. 2. please inquire about numbers of contacts other than those given above. 3. please inquire with us regarding delivery times. 4. please keep the minimum unit for ordering no less than 50 pieces per lot. 5. please inquire for further information. number of contacts all rights reserved (c) copyright matsushita electric works, ltd.
axk7, 8 notes 1. as shown below, excess force during insertion may result in damage to the connector or removal of the solder. please be careful. also, to prevent connector damage please con rm the correct position before mating connectors. 2. keep the pc board warp no more than 0.03 mm in relation to the overall length of the connector. 3. pc boards and recommended metal mask patterns connectors are mounted with high density, with a pitch interval of 0.4 to 0.5 mm. in order to reduce solder bridge and other issues make sure the proper levels of solder are used. the gures to the right are recommended metal mask patterns. please use them as a reference. 1) no retention tting socket recommended pc board pattern (top view) recommended metal mask pattern metal mask thickness: here, 150 m (opening area ratio: 40 %) recommended metal mask pattern metal mask thickness: here, 120 m (opening area ratio: 50 %) header recommended pc board pattern (top view) recommended metal mask pattern metal mask thickness: here, 150 m (opening area ratio: 32 %) recommended metal mask pattern metal mask thickness: here, 120 m (opening area ratio: 40 %) 2) with retention tting socket recommended pc board pattern (mount pad arrangement pattern) recommended metal mask pattern metal mask thickness: here, 150 m (terminal portion opening area ratio: 32 %) (metal portion opening area ratio: 65 %) recommended metal mask pattern metal mask thickness: here, 120 m (terminal portion opening area ratio: 40 %) (metal portion opening area ratio: 80 %) max. 0.03 mm max. 0.03 mm 0.115 0.05 0.40 0.05 0.40 0.05 0.40 0.05 0.23 0.03 5.70 0.05 3.50 0.05 5.50 0.01 4.48 0.01 (0.51) 0.10 0.01 0.35 0.01 0.20 0.01 0.40 0.01 (0.51) (0.63) (0.63) 0.40 0.01 0.20 0.01 5.50 0.01 4.24 0.01 0.10 0.01 0.35 0.01 0.40 0.050.40 0.05 0.23 0.03 2.96 0.05 0.115 0.05 0.40 0.05 4.56 0.05 4.10 0.01 3.50 0.01 (0.30) (0.30) 0.20 0.01 0.40 0.01 0.10 0.01 0.35 0.01 0.20 0.01 0.40 0.01 (0.37) (0.37) 4.10 0.01 3.36 0.01 0.10 0.01 0.35 0.01 (1.10) (1.10) 5.70 0.05 3.50 0.05 0.40 0.05 0.40 0.05 0.80 0.05 2.15 0.05 0.115 0.05 0.90 0.05 0.23 0.03 (0.63) (0.63) 5.50 0.01 4.24 0.01 0.80 0.01 2.15 0.01 2.15 0.01 0.72 0.01 0.10 0.01 0.20 0.01 0.35 0.01 0.40 0.01 (0.51) (0.51) 5.50 0.01 4.48 0.01 0.80 0.01 2.15 0.01 2.15 0.01 0.58 0.01 0.40 0.01 0.35 0.01 0.10 0.01 0.20 0.01 all rights reserved (c) copyright matsushita electric works, ltd.
axk7, 8 header recommended pc board pattern (mount pad arrangement pattern) recommended metal mask pattern metal mask thickness: here, 150 m (terminal portion opening area ratio: 40 %) (metal portion opening area ratio: 65 %) recommended metal mask pattern metal mask thickness: here, 120 m (terminal portion opening area ratio: 50 %) (metal portion opening area ratio: 80 %) 0.40 0.05 0.115 0.05 0.23 0.03 0.40 0.05 0.90 0.05 0.80 0.05 0.82 0.05 (0.80) (0.80) 2.96 0.05 4.56 0.05 0.35 0.01 0.10 0.01 0.40 0.01 0.20 0.01 0.82 0.01 0.82 0.01 0.58 0.01 (0.30) (0.30) 0.80 0.01 3.50 0.01 4.10 0.01 for other details, please verify with the product speci cation sheets. 0.35 0.01 0.10 0.010.20 0.01 0.40 0.01 (0.37) (0.37) 0.80 0.01 3.36 0.01 4.10 0.01 0.82 0.01 0.82 0.01 0.72 0.01 regarding sample orders to con rm proper mounting when ordering samples to con rm proper mounting with the placement machine, connectors are delivered in 50- piece units in the condition given right. consult a sale representative for ordering sample units. condition when delivered from factory required number of products for sample production embossed tape amount required for the mounting (unit 50 pieces) reel (delivery can also be made on a reel by customer request.) all rights reserved (c) copyright matsushita electric works, ltd.
axk7, 8l product types for narrow pitch connectors f4 (0.4 mm pitch) 0.9mm mated height ? : available for sale 10 16 20 22 24 26 28 30 32 34 36 38 40 44 50 54 60 70 80 ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? number of contacts p4 (0.4 mm pitch)...no retention ?ting type p4 (0.4 mm pitch)...with retention ?ting type 1.5mm mated height ? : available for sale 14 16 20 22 24 26 28 30 32 34 36 38 40 42 44 50 54 60 64 70 80 90 100 ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? 2.0mm ? ? ? ? ? ? ? 2.5mm ? ? ? 3.0mm 3.5mm 4.0mm number of contacts 1.5mm mated height ? : available for sale 10 12 20 22 30 34 40 44 46 50 60 80 90 100 ? ? * ? ? ? ? ? ? ? ? ? ? ? 2.0mm 2.5mm ? ? ? ? ? ? ? ? ? ? ? ? ? 3.0mm 3.5mm 4.0mm notes: 1. please contact us regarding numbers of contacts other than those given above. 2. * header comes with no positioning bosses. number of contacts 1.2mm mated height product name p5kl p5kf p5k p5ks ? : available for sale 10 12 14 16 18 20 22 24 26 30 32 34 36 40 50 60 70 80 100 120 130 160 ? ? ? ? ? ? ? ? ? 1.5mm ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? 2.0mm ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? 2.5mm ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? 3.0mm ? ? ? ? ? ? ? ? ? ? 3.5mm ? ? ? ? ? ? ? ? ? ? 4.0mm ? ? ? ? ? ? ? ? ? ? ? 4.5mm ? ? ? ? ? ? ? ? ? ? ? ? 5.0mm ? ? ? ? ? ? ? ? ? 5.5mm ? ? ? ? ? ? ? ? ? 6.0mm ? ? ? ? ? ? ? ? 6.5mm ? ? ? ? ? ? ? ? ? 7.0mm ? ? ? ? ? ? ? ? 8.0mm ? ? ? ? ? ? ? ? 9.0mm ? ? ? ? ? ? ? ? note: please contact us regarding numbers of contacts other than those given above. number of contacts p5kl, p5kf, p5k, and p5ks (common for 0.5 mm pitch) p5kl p5kf p5k p5ks all rights reserved (c) copyright matsushita electric works, ltd.
axk7, 8 p6s (0.6 mm pitch) 4.0mm mated height ? : available for sale 20 30 40 50 60 80 100 ? ? ? ? ? ? ? 5.0mm ? ? ? ? ? ? ? 6.0mm ? ? ? ? ? ? ? 7.0mm ? ? ? ? ? ? ? 8.0mm ? ? ? ? ? ? ? 9.0mm ? ? ? ? ? ? ? note: please contact us regarding numbers of contacts other than those given above. number of contacts floating type (0.5 mm pitch) mated height ? : available for sale 20 30 40 50 60 80 100 5.0mm ? ? ? ? ? ? ? number of contacts p8 (0.8 mm pitch) 3.0mm mated height ? : available for sale 12 14 16 20 22 24 26 30 34 40 50 60 80 90 100 ? ? ? ? ? ? ? ? ? ? ? 3.5mm ? ? ? ? ? 4.0mm ? ? ? ? ? ? ? ? ? 4.5mm ? ? ? ? 5.0mm ? ? ? ? ? ? ? ? ? ? ? 5.5mm ? ? ? ? ? 6.0mm ? ? ? ? ? ? ? ? ? 7.0mm ? ? ? ? ? ? ? ? ? 8.0mm ? ? ? ? ? ? ? ? ? ? ? 11.5mm ? ? ? ? ? 13.0mm ? ? ? ? ? ? 14.0mm ? note: please contact us regarding numbers of contacts other than those given above. number of contacts p10 (1.0 mm pitch) mated height ? : available for sale 10 16 20 30 2.0mm ? ? ? ? 2.5mm ? ? ? ? number of contacts all rights reserved (c) copyright matsushita electric works, ltd.

▲Up To Search▲

Price & Availability of AXK712125G

	To Download AXK712125G Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .